Dark Sky Approved

Dark-skyBeachside Lighting has several luminaires which are listed with the International Dark Sky Association.  To be certified, a luminaire must have 50 lumens or less in the 90-180 degree range, and less than 10 lumens in the 90-100 degree range.  The correlated color temperature (CCT) should not exceed 3000K, but does have an acceptance up to 3250K, per ANSI standards.  Given that most of our fixtures are well shielded, Dark Sky certification is another reason to consider Beachside for marine and desert environments.

  • Solid Brass Low-Voltage Fixed Downlight
    • Ideal for post mounting
    • Remote transformer required
    • Custom canopy from 1/8″ thick brass available.  Consult factory with size, shape, and thru hole orientation needed.
    Voltage 12V AC with integral driver (9V-15V Input, dimmable below 9V)
    Lamps Integrated LED
    Lumens 249 max
    CCT 1000K
    1500K
    2700K
    3000K
    Dimensions 2" dia. x 3.8″ x 1.9” extension (5.1 x 9.7 x 4.8 cm)
     
  • Solid Brass Low-Profile Marker Light
    • Remote transformer required
    Voltage 12 Volts AC/DC with integral driver (9-15V input, dimmable below 9V)
    Lamps Integrated LED, MR11 LED
    Lumens max 15
    CCT 1000K
    1500K
    2700K
    3000K
    Dimensions Dome diameter: 2.19" [5.6 cm]
    Depth: 3.14" [8.0 cm]
     
    E3-M Four-Sector Illumination (standard)
    E3-M-1 Single-Sector Illumination
    E3-M-2 Two-Sector, Adjacent Illumination
    E3-M-OP Two-Sector, Opposite Illumination
     
    (Amber Only)
  • Solid Brass, Low-profile Marker Light
    • Remote transformer required
    • In-ground or concrete installation
    Voltage 12 Volts AC / DC
    Lamps Integrated LED, MR16 LED
    CCT 1000K
    1500K
    2700K
    3000K
    Dimensions 3.5″ diameter x 5.3” depth [8.9 x 13.5 cm]
    3.8″ [9.6 cm] trim ring outer diameter
     
    E17 Four-Sector Illumination (standard)
    E17-1 Single-Sector Illumination
    E17-2 Two-Sector, Adjacent Illumination
    E17-OP Two-Sector, Opposite Illumination
     
    (Amber Only)
  • Brass & Composite In-Ground Pathlight for High Traffic & Drive-Over Applications The L-017 series in-ground drive-over fixtures are brass & composite pathlights for high-traffic areas. This low-profile fixture is ideal for paths with low ground cover and along pathways used by golf carts, service trucks, or automobiles at country clubs & resorts.
    • CR” versions add a Concrete Ring for fully recessed concrete installation.  Ring diameter is 6.7″ (17cm) and exposed height reduces to 1.7″ (4.2 cm).   [L-017-CR, L-017-C-CR]
    • Remote transformer required for 12V
    Voltage 12V, 120v, 230V
    Lamps MR16 LED
    CCT 1500K
    3000K
    Dimensions 6.5″ dia. x 1.9″ exposed height (16.5 x 4.9 cm)
     
    (Amber Only)
  • Solid Brass, Low-Voltage, Stem-Mounted Path Light
    • Ideal for walkways and tall groundcover
    • Remote transformer required
    • Custom stem lengths available
    Voltage 12 Volts AC with integral driver (9 – 15V input, dimmable below 9V)
    Lamps Integrated LED
    Lumens max 98
    CCT 1000K
    1500K
    2700K
    3000K
    Dimensions Lamp Housing: 1.6” diameter x 3.1"  [4.2 x 7.8 cm]
     
  • Beachside Lighting’s M-Series Pathlights are the ultimate in heavy-duty landscape lighting.  Made of cast brass, these fixtures are larger than other Beachside pathlights.  The omnidirectional LED lamp is protected by a threaded glass lens.  Louvers are angled at 45° to eliminate glare.  Risers are schedule 80 brass pipe.  A single-louver design also is available for use with an integrated light engine or drop-in MR16 LED. M-series pathlights with amber and red-orange LED lamps are certified as “Wildlife Friendly” by the Florida Fish & Wildlife Conservation Commission.  To view these fixtures click HERE.
    • Durable construction: all brass components
    • Stems available in three sizes: 16″, 20″ (standard), & 24
    • CSA Listed to US and Canadian safety standards, file #190030
    Voltage 12V, 120V
    Lamps LED
    CCT 1500
    2700
    3000
     
  • Beachside Lighting’s M-Series LED Pathlights are the ultimate in heavy-duty landscape lighting.  Made of cast brass, these fixtures are larger than other Beachside pathlights.  The lamp is protected by a threaded glass lens.  Louvers are angled at 45° to eliminate glare.  Risers are schedule 80 brass pipe.  M-series fixtures with a single-louver design use directional LED sources with a reflector.  A traditional multi-louver design also is available with omnidirectional LED light sources. M-series pathlights with amber and red-orange LED lamps are certified as “Wildlife Friendly” by the Florida Fish & Wildlife Conservation Commission.  To view these fixtures click HERE.
    • Durable construction: all brass components
    • Stems available in three sizes: 16″, 20″ (standard), & 24
    • CSA Listed to US and Canadian safety standards, file #190030
    Voltage 12V, 120V, 230V
    Lamps Integrated LED, MR16 LED
    CCT 1000
    1500
    2700
    3000
     
  • Beachside Lighting’s R-Series Pathlights have set the standard for durability in low-voltage walkway and area lighting.  The completely sealed fixture allows easy access to the brass lamp compartment for tool-free relamping.  Features include an 18-gauge copper shade, a 5 mm-thick frosted glass lens, and a riser made from schedule 40 brass pipe.  The lamping is G4 bi-pin LED.  The omnidirectional lamping allows for a lower profile, with most shade heights positioned so their lower edge is at the bottom of the glass, resulting in low-to-no glare. All fixtures are CSA Listed to US and Canadian safety standards, file #190030.
    • 12 Volts AC
    • Remote transformer required
    • Durable construction: all brass components and copper shades
    Voltage 12V AC
    Lamps Omnidirectional LED
    CCT 1500K
    2700K
    3000K
     
  • Solid Brass Low-Voltage Fixed Downlight
    • Remote transformer required
    Voltage 12V AC with integral driver (9V-15V Input, dimmable below 9V)
    Lamps Integrated LED
    Lumens 249 max
    CCT 1000K
    1500K
    2700K
    3000K
    Dimensions 1.6" dia. body x 2.8" dia. base x 4″ (4.2 x 7 x 10.2 cm)
     
  • Beachside Lighting’s R-Series LED Pathlights have set the standard for durability in low-voltage walkway and area lighting.  The completely sealed fixture allows easy access to the brass lamp compartment for tool-free relamping.  Features include an 18-gauge copper shade, a 5 mm-thick frosted glass lens, and a riser made from schedule 40 brass pipe.  The lamping is MR16 LED, allowing both 12V and 120V/230V options.  The upward-directed lamp hits a reflector in the shade assembly.  Most shade heights are positioned so their lower edge is at the bottom of the glass, resulting in low-to-no glare. All fixtures are CSA Listed to US and Canadian safety standards, file #190030.
    • Durable construction: all brass components and copper shades
    Voltage 12V, 120V, 230V
    Lamps LED
    CCT 1000K
    1500K
    2700K
    3000K
     
  • Solid Brass Low-Voltage Fixed Downlight
    • Ideal for post mounting
    • Remote transformer required
    • Custom canopy from 1/8″ thick brass available.  Consult factory with size, shape, and thru hole orientation needed.
    Voltage 12V AC with integral driver (9V-15V Input, dimmable below 9V)
    Lamps Integrated LED
    Lumens 123 max
    CCT 1000K
    1500K
    Dimensions 2" dia. x 3.8″ x 1.9” extension (5.1 x 9.7 x 4.8 cm)
     
  • Solid Brass, Low-Voltage, Stem-Mounted Path Light
    • Ideal for walkways and tall groundcover
    • Remote transformer required
    • Custom stem lengths available
    Voltage 12 Volts AC with integral driver (9 – 15V input, dimmable below 9V)
    Lamps Integrated LED
    Lumens max 32
    CCT 1000K
    1500K
    Dimensions Lamp Housing: 1.6” diameter x 3.1"  [4.2 x 7.8 cm]
     
  • Solid Brass Low-Voltage Fixed Downlight
    • Remote transformer required
    Voltage 12V AC with integral driver (9V-15V Input, dimmable below 9V)
    Lamps Integrated LED
    Lumens 123 max
    CCT 1000K
    1500K
    Dimensions 1.6" dia. body x 2.8" dia. base x 4″ (4.2 x 7 x 10.2 cm)
     
  • Solid Brass Low-Profile Marker Light
    • Remote transformer required
    Voltage 12 Volts AC/DC with integral driver (9-15V input, dimmable below 9V)
    Lamps Integrated LED, MR11 LED
    Lumens max 5.6
    CCT 1000K
    1500K
    Dimensions Dome diameter: 2.19" [5.6 cm]
    Depth: 3.14" [8.0 cm]
     
    E3-M Four-Sector Illumination (standard)
    E3-M-1 Single-Sector Illumination
    E3-M-2 Two-Sector, Adjacent Illumination
    E3-M-OP Two-Sector, Opposite Illumination
     
  • Solid Brass Round Louvered Steplight
    • Can be used as an uplight, steplight, or downlight in wood or masonry
    • Remote transformer required
    Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V)
    Lamps Integrated LED, MR11 LED
    Lumens 10.7 max
    CCT 1000K
    1500K
    2700K
    3000K
    Dimensions 2.17″ dia. x 3.14" depth (5.5 x 8 cm)
     
  • Solid Brass Round Louvered Steplight
    • Can be used as an steplight or downlight in wood or masonry
    • Remote transformer required
    Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V)
    Lamps Integrated LED, MR11 LED
    CCT 1000K
    1500K
    Dimensions 2.17″ dia. x 3.14" depth (5.5 x 8 cm)
     
  • Solid Brass Square Louvered Steplight
    • Can be used as an steplight or downlight in wood or masonry
    • Remote transformer required
    Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V)
    Lamps Integrated LED, MR11 LED
    CCT 1000K
    1500K
    Dimensions 2.17″ square x 3.14" depth (5.5 x 8 cm)
     
  • Solid Brass, Low-profile, Low-Voltage Directional
    • Directional downlight certified by International Dark Sky Association when mounted on VERTICAL surface and aimed downward. This fixture will not work nor be Dark Sky compliant if mounted to a horizontal surface such as the ground or ceiling.
    • Fixture comes standard with angled glare shield and Sure Aim accessory
    • Knuckle can be angled from 0° (straight down) to a maximum of 30° from vertical
    • Remote transformer required
    Voltage 12V AC/DC with integral driver (9V-15V Input, dimmable below 9V)
    Lamps Integrated LED
    Lumens 249
    CCT 1000K
    1500K
    2700K
    3000K
    Dimensions Diameter: 1.6″ (4.2cm)
    Overall length from knuckle pivot: 5.9″ (13.9cm)
     
  • Solid Brass Round Louvered Steplight
    • Remote transformer required
    • Mountable as a steplight or downlight
    • CR” versions add a Concrete Ring for fully recessed concrete installation.  Ring diameter is 3.8″ (9.6 cm) and fixture depth increases to 5.3″ (13.5 cm).   [E9-RL-CR]
    Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V)
    Lamps Integrated LED, MR16 LED
    CCT 1000K
    1500K
    Dimensions 3.5" trim dia. x 5.0" depth (8.9 x 12.6 cm)
     
  • Solid Brass Rectangular Louvered Steplight
    • Remote transformer required
    • Mountable as a steplight or downlight
    • CR” versions add a Concrete Ring for fully recessed concrete installation.  Ring is 3.3 x 4.3″ (8.3 x 10.9 cm) and fixture depth increases to 5.3″ (13.5 cm).   [E9-RCL-CR]
    Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V)
    Lamps Integrated LED, MR16 LED
    CCT 1000K
    1500K
    Dimensions 3 x 4" trim, 5.0" depth (7.6 x 10.2 cm, 12.6 cm)
     
  • Solid Brass Square Louvered Steplight
    • Remote transformer required
    • Mountable as a steplight or downlight
    • CR” versions add a Concrete Ring for fully recessed concrete installation.  Ring is 4.3″ square (10.9 cm) and fixture depth increases to 5.3″ (13.5 cm).   [E9-SQL-CR]
    Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V)
    Lamps Integrated LED, MR16 LED
    CCT 1000K
    1500K
    Dimensions 4" square trim x 5.0" depth (10 x 12.6 cm)
     
  • Solid Brass, All-purpose, Low-voltage LED Directional The E16-30-BGS-SA is a low-voltage directional luminaire with an integrated, replaceable LED light engine.  The warm white light engines features four output settings from 100% to 25%, adjustable in the field.
    • Directional downlight certified by International Dark Sky Association when mounted on VERTICAL surface and aimed downward. This fixture will not work nor be Dark Sky compliant if mounted to a horizontal surface such as the ground or ceiling.
    • Fixture comes standard with angled glare shield and Sure Aim accessory
    • Knuckle can be angled from 0 (straight down) to a maximum of 30o from vertical
    • Remote transformer required
    Voltage 12V AC/DC with integral driver (9V-15V Input, dimmable below 9V)
    Lamps Integrated LED
    Lumens 799 max
    CCT 1000K (Red-Orange, 630nm)
    1500K (Amber, 595nm)
    2700K
    3000K
    Dimensions Diameter: 2.4" (6 cm)
    Overall length from knuckle pivot: 7.3" (18.4 cm)
     
  • Solid Brass, Low-profile Marker Light
    • Remote transformer required
    • In-ground or concrete installation
    Voltage 12 Volts AC / DC
    Lamps Integrated LED, MR16 LED
    CCT 1000K
    1500K
    Dimensions 3.5″ diameter x 5.3” depth [8.9 x 13.5 cm]
    3.8″ [9.6 cm] trim ring outer diameter
     
    E17 Four-Sector Illumination (standard)
    E17-1 Single-Sector Illumination
    E17-2 Two-Sector, Adjacent Illumination
    E17-OP Two-Sector, Opposite Illumination
     
  • Solid Brass Fixed Downlight
    • Lamp is recessed for glare reduction
    • Remote transformer required for 12V
    Voltage 12V, 120V, 230V
    Lamps Integrated LED, MR16 LED
    Lumens 338 max (8W)
    CCT 1000K
    1500K
    Dimensions 2.4" dia. body x 4.75" dia. base x 4.7″ (6 x 12.1 x 12 cm)
     
  • Recessed Cast Brass Steplight The L-012 is a recessed, low-voltage steplight that uses an MR16 lamp and is available with clear, frosted, and rectilinear spread glass lenses.
    • Remote transformer required
    • Suitable for combustible and non-combustible mounting surfaces
    • Suitable for indoor or outdoor use
    Voltage 12V AC/DC
    Lamps MR16 LED
    CCT 1500
    Dimensions Faceplate: 4.4″ dia. x 2.1″ extension (11.2 x 5.3 cm)
    PVC rough-in housing: 2-7/8″ dia. x 5.1″ deep (7.3 x 13 cm)
     
  • Wall-Mounted Brass Downlight
    • Remote transformer required for 12V
    • Certified for indoor (12V) or outdoor use
    Voltage 12V, 120V, 230V
    Lamps Integrated LED light engine, MR16 LED
    Lumens 372 max
    CCT 1000K
    1300K
    1500K
    Dimensions 5.9"/14.9 cm tall (MR16), 6.6"/16.8 cm tall (light engine)
    2.4" dia lamp body x 3.7" extension from wall (6 x 9.3 cm)
     
  • Solid Brass Square Louvered Steplight
    • Can be used as an uplight, steplight, or downlight in wood or masonry
    • Remote transformer required
    Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V)
    Lamps Integrated LED, MR11 LED
    Lumens 15.4 max
    CCT 1000K
    1500K
    2700K
    3000K
    Dimensions 2.17″ square x 3.14" depth (5.5 x 8 cm)
     
  • Solid Brass Round Louvered Steplight
    • Remote transformer required
    • Mountable as a steplight, uplight, or downlight
    • CR” versions add a Concrete Ring for fully recessed concrete installation.  Ring diameter is 3.8″ (9.6 cm) and fixture depth increases to 5.3″ (13.5 cm).   [E9-RL-CR]
    Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V)
    Lamps Integrated LED, MR16 LED
    CCT 1000K
    1500K
    2700K
    3000K
    Dimensions 3.5" trim dia. x 5.0" depth (8.9 x 12.6 cm)
     

Title

Go to Top