2W-A-SP | 10° |
2W-A-NFL | 30° |
2W-A-FL | 50° |
Over the last three decades, greater attention has been given to one particular plight of sea turtles in coastal areas: beach lighting. Sea turtles coming to the shore to lay eggs will get disoriented by artificial light, which can keep them from nesting. For those that do nest, their hatchlings may be tricked into going toward man-made lighting sources instead of the instinctively attractive starlight or moonlight reflecting off the water. Once traveling in the wrong direction, a hatchling can become dehydrated, be prey for land-based predators, or even be run over by an automobile. Beachside Lighting has worked closely with the Florida Fish & Wildlife Conservation Commission to offer turtle-safe lighting fixtures that accept low-wattage / long-wavelength amber LED sources.
Of course, Beachside fixtures are solid brass to withstand the elements at installations near the ocean. Below are some of our approved fixtures. View the complete line of approved fixtures on the Florida Fish and Wildlife Conservation Commission’s website, including additional Beachside fixtures.
-
Solid Brass Low-Voltage Fixed Downlight
- Ideal for post mounting
- Remote transformer required
- Custom canopy from 1/8″ thick brass available. Consult factory with size, shape, and thru hole orientation needed.
Voltage 12V AC with integral driver (9V-15V Input, dimmable below 9V) Lamps Integrated LED Lumens 123 max CCT 1000K 1500K Dimensions 2" dia. x 3.8″ x 1.9” extension (5.1 x 9.7 x 4.8 cm) -
Solid Brass, Low-Voltage, Stem-Mounted Path Light
- Ideal for walkways and tall groundcover
- Remote transformer required
- Custom stem lengths available
Voltage 12 Volts AC with integral driver (9 – 15V input, dimmable below 9V) Lamps Integrated LED Lumens max 32 CCT 1000K 1500K Dimensions Lamp Housing: 1.6” diameter x 3.1" [4.2 x 7.8 cm] -
Solid Brass Low-Profile Marker Light
- Remote transformer required
Voltage 12 Volts AC/DC with integral driver (9-15V input, dimmable below 9V) Lamps Integrated LED, MR11 LED Lumens max 5.6 CCT 1000K 1500K (DarkSky approved) Dimensions Dome diameter: 2.19" [5.6 cm] Depth: 3.14" [8.0 cm] E3-M Four-Sector Illumination (standard) E3-M-1 Single-Sector Illumination E3-M-2 Two-Sector, Adjacent Illumination E3-M-OP Two-Sector, Opposite Illumination -
Solid Brass Square Louvered Steplight
- Can be used as an steplight or downlight in wood or masonry
- Remote transformer required
Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V) Lamps Integrated LED, MR11 LED CCT 1000K 1500K Dimensions 2.17″ square x 3.14" depth (5.5 x 8 cm) -
Solid Brass, Low-profile, Low-Voltage Directional
- Directional downlight certified by International Dark Sky Association when mounted on VERTICAL surface and aimed downward. This fixture will not work nor be Dark Sky compliant if mounted to a horizontal surface such as the ground or ceiling.
- Fixture comes standard with angled glare shield and Sure Aim accessory
- Knuckle can be angled from 0° (straight down) to a maximum of 30° from vertical
- Remote transformer required
Voltage 12V AC/DC with integral driver (9V-15V Input, dimmable below 9V) Lamps Integrated LED Lumens 123 max CCT 1000K 1500K Dimensions Diameter: 1.6″ (4.2cm) Overall length from knuckle pivot: 5.9″ (13.9cm) -
Solid Brass, Low-Profile, Hanging Downlight
- Supplied with 20″ stainless steel cable, 36″ lead wire, and 1/2″ male fitting for mounting accessory
- Can also be hung directly by loop
- Remote transformer required
Voltage 12V AC/DC with integral driver (9V-15V Input, dimmable below 9V) Lamps Integrated LED Lumens max 123 CCT 1000K 1500K Dimensions 1.6″ dia. x 3.25" (4.2 x 8.3 cm) -
Solid Brass Round Louvered Steplight
- Remote transformer required
- Mountable as a steplight or downlight
- “CR” versions add a Concrete Ring for fully recessed concrete installation. Ring diameter is 3.8″ (9.6 cm) and fixture depth increases to 5.3″ (13.5 cm). [E9-RL-CR]
Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V) Lamps Integrated LED, MR16 LED CCT 1000K 1500K Dimensions 3.5" trim dia. x 5.0" depth (8.9 x 12.6 cm) -
Solid Brass Rectangular Louvered Steplight
- Remote transformer required
- Mountable as a steplight or downlight
- “CR” versions add a Concrete Ring for fully recessed concrete installation. Ring is 3.3 x 4.3″ (8.3 x 10.9 cm) and fixture depth increases to 5.3″ (13.5 cm). [E9-RCL-CR]
Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V) Lamps Integrated LED, MR16 LED CCT 1000K 1500K Dimensions 3 x 4" trim, 5.0" depth (7.6 x 10.2 cm, 12.6 cm) -
Solid Brass Square Louvered Steplight
- Remote transformer required
- Mountable as a steplight or downlight
- “CR” versions add a Concrete Ring for fully recessed concrete installation. Ring is 4.3″ square (10.9 cm) and fixture depth increases to 5.3″ (13.5 cm). [E9-SQL-CR]
Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V) Lamps Integrated LED, MR16 LED CCT 1000K 1500K Dimensions 4" square trim x 5.0" depth (10 x 12.6 cm) -
Solid Brass, All-purpose, Low-voltage LED Directional The E16-30-BGS-SA-WL is a low-voltage directional luminaire with an integrated, replaceable LED light engine.
- Directional downlight certified by International Dark Sky Association when mounted on VERTICAL surface and aimed downward. This fixture will not work nor be Dark Sky compliant if mounted to a horizontal surface such as the ground or ceiling.
- Fixture comes standard with angled glare shield and Sure Aim accessory
- Knuckle can be angled from 0o (straight down) to a maximum of 30o from vertical
- Remote transformer required
Voltage 12V AC/DC with integral driver (9V-15V Input, dimmable below 9V) Lamps Integrated LED Lumens 372 max CCT 1000K (Red-Orange, 630nm) 1500K (Amber, 595nm) Dimensions Diameter: 2.4" (6 cm) Overall length from knuckle pivot: 7.3" (18.4 cm) -
Solid Brass, Low-profile Marker Light
- Remote transformer required
- In-ground or concrete installation
Voltage 12 Volts AC / DC Lamps Integrated LED, MR16 LED CCT 1000K 1500K (DarkSky approved) Dimensions 3.5″ diameter x 5.3” depth [8.9 x 13.5 cm] 3.8″ [9.6 cm] trim ring outer diameter E17 Four-Sector Illumination (standard) E17-1 Single-Sector Illumination E17-2 Two-Sector, Adjacent Illumination E17-OP Two-Sector, Opposite Illumination -
Solid Brass, All-Purpose Directional
- Directional downlight certified by International Dark Sky Association when mounted on VERTICAL surface and aimed downward. This fixture will not work nor be Dark Sky compliant if mounted to a horizontal surface such as the ground or ceiling.
- Fixture comes standard with angled glare shield and Sure Aim accessory
- Knuckle can be angled from 0o (straight down) to a maximum of 30o from vertical
- Remote transformer required for 12V
Voltage 12V, 120V Lamps MR16 LED Lumens 79 max CCT 1500K Dimensions Diameter: 2.4" (6 cm) Overall length from knuckle pivot: 7.3″ (18.4 cm) -
Recessed Cast Brass Steplight The L-012 is a recessed, low-voltage steplight that uses an MR16 lamp and is available with clear, frosted, and rectilinear spread glass lenses.
- Remote transformer required
- Suitable for combustible and non-combustible mounting surfaces
- Suitable for indoor or outdoor use
Voltage 12V AC/DC Lamps MR16 LED CCT 1500 Dimensions Faceplate: 4.4″ dia. x 2.1″ extension (11.2 x 5.3 cm) PVC rough-in housing: 2-7/8″ dia. x 5.1″ deep (7.3 x 13 cm) -
Wall-Mounted Brass Downlight
- Remote transformer required for 12V
- Certified for indoor (12V) or outdoor use
Voltage 12V, 120V, 230V Lamps Integrated LED light engine, MR16 LED Lumens 372 max CCT 1000K 1300K 1500K Dimensions 5.9"/14.9 cm tall (MR16), 6.6"/16.8 cm tall (light engine) 2.4" dia lamp body x 3.7" extension from wall (6 x 9.3 cm) -
L-016: New Construction L-016R: Remodel
- Rotation ring and angling bracket allow aiming in any direction
- Cast brass trim
- Suitable for wet locations
- Suitable for indoor use when equipped with integrated light engine
Voltage 12V with integral magnetic transformer Lamps Integrated LED, MR16 LED Lumens 212 max CCT 1000K 1500K Faceplate Dimensions 5" dia x 0.8" high (12.7 x 2.1 cm) -
L-016-F: New Construction L-016R-F: Remodel
- Rotation ring and angling bracket allow aiming in any direction
- FLAT ROUND brass trim
- Suitable for wet locations
- Suitable for indoor use when equipped with integrated light engine
Voltage 12V with integral magnetic transformer Lamps Integrated LED, MR16 LED Lumens 212 max CCT 1000K 1500K Faceplate Dimensions 5" dia x 0.2" thick (12.7 x 0.4 cm) -
L-016-SQ: New Construction L-016R-SQ: Remodel
- Rotation ring and angling bracket allow aiming in any direction
- FLAT SQUARE brass trim
- Suitable for wet locations
- Suitable for indoor use when equipped with integrated light engine
Voltage 12V with integral magnetic transformer Lamps Integrated LED, MR16 LED Lumens 212 max CCT 1000K 1500K Faceplate Dimensions 5" square x 0.2" thick (12.7 x 0.4 cm) -
Brass & Composite In-Ground Pathlight for High Traffic & Drive-Over Applications The L-017 series in-ground drive-over fixtures are brass & composite pathlights for high-traffic areas. This low-profile fixture is ideal for paths with low ground cover and along pathways used by golf carts, service trucks, or automobiles at country clubs & resorts.
- “CR” versions add a Concrete Ring for fully recessed concrete installation. Ring diameter is 6.7″ (17cm) and exposed height reduces to 1.7″ (4.2 cm). [L-017-CR, L-017-C-CR]
- Remote transformer required for 12V
Voltage 12V, 120v, 230V Lamps MR16 LED CCT 1500K Dimensions 6.5″ dia. x 1.9″ exposed height (16.5 x 4.9 cm) -
FFWCC Wildlife Certification # 2018-029 Beachside Lighting’s M-Series LED Pathlights are the ultimate in heavy-duty landscape lighting. Made of cast brass, these fixtures are larger than other Beachside pathlights. The lamp is protected by a threaded glass lens. Risers are schedule 80 brass pipe.
- Remote transformer required for 12V
- Durable construction: all brass components
- Stems available in three sizes: 16″, 20″ (standard), & 24″
- CSA Listed to US and Canadian safety standards, file #190030
Voltage 12V, 120V, 230V Lamps Integrated LED, MR16 LED CCT 1000 1500 -
FFWCC Wildlife Certification # 2018-029 Beachside Lighting’s M-Series LED Pathlights are the ultimate in heavy-duty landscape lighting. Made of cast brass, these fixtures are larger than other Beachside pathlights. The lamp is protected by a threaded glass lens. Risers are schedule 80 brass pipe.
- Remote transformer required for 12V
- Durable construction: all brass components
- Stems available in three sizes: 16″, 20″ (standard), & 24″
- CSA Listed to US and Canadian safety standards, file #190030
Voltage 12V, 120V, 230V Lamps Integrated LED, MR16 LED CCT 1000 1500 -
FFWCC Wildlife Certification # 2018-029 Beachside Lighting’s M-Series LED Pathlights are the ultimate in heavy-duty landscape lighting. Made of cast brass, these fixtures are larger than other Beachside pathlights. The lamp is protected by a threaded glass lens. Risers are schedule 80 brass pipe.
- Remote transformer required for 12V
- Durable construction: all brass components
- Stems available in three sizes: 16″, 20″ (standard), & 24″
- CSA Listed to US and Canadian safety standards, file #190030
Voltage 12V, 120V, 230V Lamps Integrated LED, MR16 LED CCT 1000 1500