Turtle Friendly

Over the last three decades, greater attention has been given to one particular plight of sea turtles in coastal areas: beach lighting. Sea turtles coming to the shore to lay eggs will get disoriented by artificial light, which can keep them from nesting. For those that do nest, their hatchlings may be tricked into going toward man-made lighting sources instead of the instinctively attractive starlight or moonlight reflecting off the water. Once traveling in the wrong direction, a hatchling can become dehydrated, be prey for land-based predators, or even be run over by an automobile. Beachside Lighting has worked closely with the Florida Fish & Wildlife Conservation Commission to offer turtle-safe lighting fixtures that accept low-wattage / long-wavelength amber LED sources.

Of course, Beachside fixtures are solid brass to withstand the elements at installations near the ocean. Below are some of our approved fixtures. View the complete line of approved fixtures on the Florida Fish and Wildlife Conservation Commission’s website, including additional Beachside fixtures.

  • 2 Watt Amber LED module (1600K) certified by Florida Fish & Wildlife Conservation Commission as "Wildlife Friendly".  
    2W-A-SP 10°
    2W-A-NFL 30°
    2W-A-FL 50°
  • Solid Brass, Low-Voltage, Stem-Mounted Path Light
    • Ideal for walkways and tall groundcover
    • Remote transformer required
    • Custom stem lengths available
    Voltage 12 Volts AC with integral driver (9 – 15V input, dimmable below 9V)
    Lamps Integrated LED
    Lumens max 32
    CCT 1000K
    1500K
    Dimensions Lamp Housing: 1.6” diameter x 3.1"  [4.2 x 7.8 cm]
     
  • Solid Brass Low-Voltage Fixed Downlight
    • Ideal for post mounting
    • Remote transformer required
    • Custom canopy from 1/8″ thick brass available.  Consult factory with size, shape, and thru hole orientation needed.
    Voltage 12V AC with integral driver (9V-15V Input, dimmable below 9V)
    Lamps Integrated LED
    Lumens 123 max
    CCT 1000K
    1500K
    Dimensions 2" dia. x 3.8″ x 1.9” extension (5.1 x 9.7 x 4.8 cm)
     
  • Solid Brass, Low-profile Marker Light
    • Remote transformer required
    • In-ground or concrete installation
    Voltage 12 Volts AC / DC
    Lamps Integrated LED, MR16 LED
    CCT 1000K
    1500K
    Dimensions 3.5″ diameter x 5.3” depth [8.9 x 13.5 cm]
    3.8″ [9.6 cm] trim ring outer diameter
     
    E17 Four-Sector Illumination (standard)
    E17-1 Single-Sector Illumination
    E17-2 Two-Sector, Adjacent Illumination
    E17-OP Two-Sector, Opposite Illumination
     
  • Solid Brass Low-Voltage Fixed Downlight
    • Remote transformer required
    Voltage 12V AC with integral driver (9V-15V Input, dimmable below 9V)
    Lamps Integrated LED
    Lumens 123 max
    CCT 1000K
    1500K
    Dimensions 1.6" dia. body x 2.8" dia. base x 4″ (4.2 x 7 x 10.2 cm)
     
  • Solid Brass Low-Profile Marker Light
    • Remote transformer required
    Voltage 12 Volts AC/DC with integral driver (9-15V input, dimmable below 9V)
    Lamps Integrated LED, MR11 LED
    Lumens max 5.6
    CCT 1000K
    1500K
    Dimensions Dome diameter: 2.19" [5.6 cm]
    Depth: 3.14" [8.0 cm]
     
    E3-M Four-Sector Illumination (standard)
    E3-M-1 Single-Sector Illumination
    E3-M-2 Two-Sector, Adjacent Illumination
    E3-M-OP Two-Sector, Opposite Illumination
     
  • Solid Brass Round Louvered Steplight
    • Can be used as an steplight or downlight in wood or masonry
    • Remote transformer required
    Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V)
    Lamps Integrated LED, MR11 LED
    CCT 1000K
    1500K
    Dimensions 2.17″ dia. x 3.14" depth (5.5 x 8 cm)
     
  • Solid Brass Square Louvered Steplight
    • Can be used as an steplight or downlight in wood or masonry
    • Remote transformer required
    Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V)
    Lamps Integrated LED, MR11 LED
    CCT 1000K
    1500K
    Dimensions 2.17″ square x 3.14" depth (5.5 x 8 cm)
     
  • Solid Brass, Low-Profile, Hanging Downlight
    • Supplied with 20″ stainless steel cable, 36″ lead wire, and 1/2″ male fitting for mounting accessory
    • Can also be hung directly by loop
    • Remote transformer required
    Voltage 12V AC/DC with integral driver (9V-15V Input, dimmable below 9V)
    Lamps Integrated LED
    Lumens max 123
    CCT 1000K
    1500K
    Dimensions 1.6″ dia. x  3.25" (4.2 x 8.3 cm)
  • Solid Brass Rectangular Louvered Steplight
    • Remote transformer required
    • Mountable as a steplight or downlight
    • CR” versions add a Concrete Ring for fully recessed concrete installation.  Ring is 3.3 x 4.3″ (8.3 x 10.9 cm) and fixture depth increases to 5.3″ (13.5 cm).   [E9-RCL-CR]
    Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V)
    Lamps Integrated LED, MR16 LED
    CCT 1000K
    1500K
    Dimensions 3 x 4" trim, 5.0" depth (7.6 x 10.2 cm, 12.6 cm)
     
  • Solid Brass Round Louvered Steplight
    • Remote transformer required
    • Mountable as a steplight or downlight
    • CR” versions add a Concrete Ring for fully recessed concrete installation.  Ring diameter is 3.8″ (9.6 cm) and fixture depth increases to 5.3″ (13.5 cm).   [E9-RL-CR]
    Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V)
    Lamps Integrated LED, MR16 LED
    CCT 1000K
    1500K
    Dimensions 3.5" trim dia. x 5.0" depth (8.9 x 12.6 cm)
     
  • Solid Brass Square Louvered Steplight
    • Remote transformer required
    • Mountable as a steplight or downlight
    • CR” versions add a Concrete Ring for fully recessed concrete installation.  Ring is 4.3″ square (10.9 cm) and fixture depth increases to 5.3″ (13.5 cm).   [E9-SQL-CR]
    Voltage 12V AC/DC (LEDs with integral driver 9V-15V Input, dimmable below 9V)
    Lamps Integrated LED, MR16 LED
    CCT 1000K
    1500K
    Dimensions 4" square trim x 5.0" depth (10 x 12.6 cm)
     
  • Solid Brass Fixed Downlight
    • Lamp is recessed for glare reduction
    • Remote transformer required for 12V
    Voltage 12V, 120V, 230V
    Lamps Integrated LED, MR16 LED
    Lumens 338 max (8W)
    CCT 1000K
    1500K
    Dimensions 2.4" dia. body x 4.75" dia. base x 4.7″ (6 x 12.1 x 12 cm)
     
  • Recessed Cast Brass Steplight The L-012 is a recessed, low-voltage steplight that uses an MR16 lamp and is available with clear, frosted, and rectilinear spread glass lenses.
    • Remote transformer required
    • Suitable for combustible and non-combustible mounting surfaces
    • Suitable for indoor or outdoor use
    Voltage 12V AC/DC
    Lamps MR16 LED
    CCT 1500
    Dimensions Faceplate: 4.4″ dia. x 2.1″ extension (11.2 x 5.3 cm)
    PVC rough-in housing: 2-7/8″ dia. x 5.1″ deep (7.3 x 13 cm)
     
  • Wall-Mounted Brass Downlight
    • Remote transformer required for 12V
    • Certified for indoor (12V) or outdoor use
    Voltage 12V, 120V, 230V
    Lamps Integrated LED light engine, MR16 LED
    Lumens 372 max
    CCT 1000K
    1300K
    1500K
    Dimensions 5.9"/14.9 cm tall (MR16), 6.6"/16.8 cm tall (light engine)
    2.4" dia lamp body x 3.7" extension from wall (6 x 9.3 cm)
     
  • L-016:  New Construction L-016R:  Remodel
    • Rotation ring and angling bracket allow aiming in any direction
    • Cast brass trim
    • Suitable for wet locations
    • Suitable for indoor use when equipped with integrated light engine
    Voltage 12V with integral magnetic transformer
    Lamps Integrated LED, MR16 LED
    Lumens 212 max
    CCT 1000K
    1500K
    Faceplate Dimensions 5" dia x 0.8" high (12.7 x 2.1 cm)
     
  • L-016-F:  New Construction L-016R-F:  Remodel
    • Rotation ring and angling bracket allow aiming in any direction
    • FLAT ROUND brass trim
    • Suitable for wet locations
    • Suitable for indoor use when equipped with integrated light engine
    Voltage 12V with integral magnetic transformer
    Lamps Integrated LED, MR16 LED
    Lumens 212 max
    CCT 1000K
    1500K
    Faceplate Dimensions 5" dia x 0.2" thick (12.7 x 0.4 cm)
     
  • L-016-SQ:  New Construction L-016R-SQ:  Remodel
    • Rotation ring and angling bracket allow aiming in any direction
    • FLAT SQUARE brass trim
    • Suitable for wet locations
    • Suitable for indoor use when equipped with integrated light engine
    Voltage 12V with integral magnetic transformer
    Lamps Integrated LED, MR16 LED
    Lumens 212 max
    CCT 1000K
    1500K
    Faceplate Dimensions 5" square x 0.2" thick (12.7 x 0.4 cm)
     
  • Brass & Composite In-Ground Pathlight for High Traffic & Drive-Over Applications The L-017 series in-ground drive-over fixtures are brass & composite pathlights for high-traffic areas. This low-profile fixture is ideal for paths with low ground cover and along pathways used by golf carts, service trucks, or automobiles at country clubs & resorts.
    • CR” versions add a Concrete Ring for fully recessed concrete installation.  Ring diameter is 6.7″ (17cm) and exposed height reduces to 1.7″ (4.2 cm).   [L-017-CR, L-017-C-CR]
    • Remote transformer required for 12V
    Voltage 12V, 120v, 230V
    Lamps MR16 LED
    CCT 1500K
    Dimensions 6.5″ dia. x 1.9″ exposed height (16.5 x 4.9 cm)
     
  • Cast Brass Recessed Steplight Beachside Lighting's L-018 rectangular recessed solid brass step light is a marine grade landscape lighting fixture ideal for illumination of stairs, steps, and hardscapes.  It uses MR16 lamps and has a minimal extension from the wall.  Shown with Nickel finish.
    • Remote transformer required for 12V
    • Durable construction—cast brass components
    • Louvers angled to 30° to eliminate glare
    • Non-combustible (masonry) installation only
    Voltage 12V, 120V
    Lamps MR16 LED
    Lumens 11 max
    CCT 1500K
    Dimensions 3.3" x 5.3" x 5" deep (8.3 x 13.3 x 12.6 cm)
  • FFWCC Wildlife Certification # 2018-029 Beachside Lighting’s M-Series LED Pathlights are the ultimate in heavy-duty landscape lighting.  Made of cast brass, these fixtures are larger than other Beachside pathlights.  The lamp is protected by a threaded glass lens.  Risers are schedule 80 brass pipe.
    • Remote transformer required for 12V
    • Durable construction: all brass components
    • Stems available in three sizes: 16″, 20″ (standard), & 24
    • CSA Listed to US and Canadian safety standards, file #190030
    Voltage 12V, 120V, 230V
    Lamps Integrated LED, MR16 LED
    CCT 1000
    1500
  • FFWCC Wildlife Certification # 2018-029 Beachside Lighting’s M-Series LED Pathlights are the ultimate in heavy-duty landscape lighting.  Made of cast brass, these fixtures are larger than other Beachside pathlights.  The lamp is protected by a threaded glass lens.  Risers are schedule 80 brass pipe.
    • Remote transformer required for 12V
    • Durable construction: all brass components
    • Stems available in three sizes: 16″, 20″ (standard), & 24
    • CSA Listed to US and Canadian safety standards, file #190030
    Voltage 12V, 120V, 230V
    Lamps Integrated LED, MR16 LED
    CCT 1000
    1500
  • FFWCC Wildlife Certification # 2018-029 Beachside Lighting’s M-Series LED Pathlights are the ultimate in heavy-duty landscape lighting.  Made of cast brass, these fixtures are larger than other Beachside pathlights.  The lamp is protected by a threaded glass lens.  Risers are schedule 80 brass pipe.
    • Remote transformer required for 12V
    • Durable construction: all brass components
    • Stems available in three sizes: 16″, 20″ (standard), & 24
    • CSA Listed to US and Canadian safety standards, file #190030
    Voltage 12V, 120V, 230V
    Lamps Integrated LED, MR16 LED
    CCT 1000
    1500
  • FFWCC Wildlife Certification # 2018-029 Beachside Lighting’s M-Series LED Pathlights are the ultimate in heavy-duty landscape lighting.  Made of cast brass, these fixtures are larger than other Beachside pathlights.  The lamp is protected by a threaded glass lens.  Risers are schedule 80 brass pipe.
    • Remote transformer required for 12V
    • Durable construction: all brass components
    • Stems available in three sizes: 16″, 20″ (standard), & 24
    • CSA Listed to US and Canadian safety standards, file #190030
    Voltage 12V, 120V, 230V
    Lamps Integrated LED, MR16 LED
    CCT 1000
    1500
  • FFWCC Wildlife Certification # 2018-029 Beachside Lighting’s M-Series LED Pathlights are the ultimate in heavy-duty landscape lighting.  Made of cast brass, these fixtures are larger than other Beachside pathlights.  The lamp is protected by a threaded glass lens.  Risers are schedule 80 brass pipe.
    • Remote transformer required for 12V
    • Durable construction: all brass components
    • Stems available in three sizes: 16″, 20″ (standard), & 24
    • CSA Listed to US and Canadian safety standards, file #190030
    Voltage 12V, 120V, 230V
    Lamps Integrated LED, MR16 LED
    CCT 1000
    1500
  • Classic-Style Bollard for Concrete Installation FFWCC Wildlife Certification # 2018-029 The MB1 is an unobtrusive, contemporary pathlight/bollard hybrid with 180° illumination via the field-rotatable top assembly.
    • 360° illumination option (MB1-360)
    • Durable construction – all brass components
    • Can be mounted on optional stems
    • Custom fixture heights available
    Voltage 12V, 120V, 230V, 277V
    Lamps Integrated LED
    Lumens max 4.6
    CCT 1000
    1500
    Dimensions 1.6″ diameter x 16.9″ height (4.1 x 42.8 cm)
     
  • FFWCC Wildlife Certification # 2018-029 Beachside Lighting’s MB-Series bollards set the standard for durable, corrosion-resistant walkway lighting.  These LED models use a cast brass, single-louver design.  The lamp is protected by a threaded glass lens.  An internal brass collar with stainless steel mounting hardware helps ensure stability.  Standard shaft heights are 4, 12, and 28 inches; custom shaft heights are available.
    • Remote transformer required for 12V.
    • Durable construction: all brass components and shades
    • CSA Listed to US and Canadian safety standards, file # 190030
    Voltage 12V, 120V, 230V
    Lamps Integrated LED, MR16 LED
    CCT 1000K
    1500K
     
  • Contemporary Brass Bollard FFWCC Wildlife Certification # 2019-231  
    • Remote transformer required for 12V
    • Durable construction: all brass components
    • Mountable on brass base, junction box, or ground spike
    • Available in 9"/22 cm and 20"/51 cm nominal heights (w/o base)
    • Comes equipped with HS-MB4-270 optical accessory for 90° illumination
    • CSA Listed to US and Canadian safety standards, file # 190030
    Voltage 12V, 120V
    Lamps Integrated LED, MR16 LED
    Lumens 35 max
    CCT 1500K
    Dimensions:  9" 2.4″ dia. x 8.7″ (6.1 x 22 cm)
    20" 2.4″ dia. x 20″ (6.1 x 50.8 cm)
     

Title

Go to Top