• Rough Sand Cast Round Brass Canopy with Convex Contour
    • 4.5" canopy diameter x 0.7" height (11.4 x 1.7 cm)
    • This series must be used if a SMB accessory is specified
    CM Substitution accessory for L-013 & L-014 Series fixtures, slip-fit center hole
    CM1 Substitution accessory for L-011-CM1, one center 1/2" tap
    CM2 Substitution accessory for L-011-CM2, two 1/2" taps
    CM3 Substitution accessory for L-011-CM2 with motion sensor, three 1/2" taps
     
    Specifications
  • Machined Round Brass Canopy Standard mounting plate with all Beachside wall mount fixtures.
    • 4.75" diameter x 0.5" thick (12.1 x 1.4 cm)
    • Supplied with brass crossbar for standard 2.75" and 3.5" hole spacing and single-gang boxes.
    • Supplied with gasket and black stainless steel screws
    CM-M One slip-fit center hole.  Standard with L-013, L-014, L-023, & L-024
    CM-M1 One 1/2" tap for single fixture.  Standard with L-011-CM1
    CM-M2 Two 1/2" taps for dual fixture.  Standard with L-011-CM2
    CM-M3 Three 1/2" taps for dual fixture + Motion Sensor.  Standard with L-011-CM2 with MS.
     
    Specifications Brass Crossbar Specifications (included with canopy)
  • Low-Profile Round Brass Canopy For Monopoint Directional Fixtures Using SA Accessory
    • 3.25" dia. x 0.375" tall (8.3 cm x 9.5 mm)
    • Includes corrosion-resistant brass wood screws
    Specifications
  • Brass Rotation Mount Standard male-threaded knuckle half is replaced with SA (threaded into canopy, fixed) and mating female knuckle half.  Allows for locking rotation using a set screw without removing the canopy.  Directional fixtures only. Specifications
  • Rectangular Machined Brass Mounting Plate
    • For use with Beachside's wall-mounted fixtures in conjunction with the SGBOX-SS or any other single-gang junction box
    • 4.6" high x 2.9" wide x 0.25" thick (11.7 x 7.3 cm x 6.4 mm)
    SGCM Substitution accessory for L-013, L-014, L-023, and L-024 fixtures; slip-fit center hole
    SGCM1 Substitution accessory for wall-mounted directionals; single 1/2" threaded hole
      Specifications
  • Round Brass Surface/Wall Mounted Box Ideal for locations without a recessed box.  Accepts CM, CM1, and CM2 canopies (not included).  Two 1/2" taps in back allow conduit connection.  Four holes in back allow mounting to wall or existing "pancake" box.  SMB can accommodate two T75 transformers. 4.7" diameter x 1.75" (2.3" with canopy) (11.9 x 4.4/5.8 cm) Specifications
  • Machined Square Brass Canopy
    • Supplied with brass crossbar for standard 2.75" and 3.5" hole spacing and single-gang boxes.
    • Supplied with gasket and black stainless steel screws
    • Dimensions: 4.75" square x 0.5" thick (12.1 x 1.4 cm)
    SQ One slip-fit center hole.  Substitution accessory for Beachside fixtures using a straight arm, including L-013 & L-014 series, L-023, and L-024.
    SQ1 One 1/2" tap for single fixture.  Substitution accessory for Beachside fixtures using standard knuckle or SA accessory, including E16 and L-011-CM & L-011-P-CM series fixtures.
    SQ2 Two 1/2" taps for dual fixture.  Substitution accessory for dual-head models (L-011-CM2, L-011-P-CM2)
    SQ3 Three 1/2" taps for dual fixture + Motion Sensor.  Standard with L-011-CM2 with MS.
      Specifications Brass Crossbar Specifications (included with canopy)
  • Small Square Brass Canopy
    • Two-part design eliminates front-facing fasteners
    • Mounting holes on back bracket at 2.75" b.c. fit standard 3.5" round or octagonal junction box
    • Dimensions: 3.5" square x 0.5" thick (8.9 x 1.3 cm)
    SQ-3.5 Square canopy with slip fitting for use with any Beachside fixture using a straight arm, including L-013-S, L-014-S, L-023, and L-024 models.
    SQ1-3.5 Square canopy with 1/2" tap for use with any Beachside fixture using standard knuckle or SA accessory, including E8 and L-011 series fixtures.
      Specifications
  • Tree / Beam Mount For Monopoint Directional Fixtures Using SA Accessory Made from .063" thick spun yellow brass.  Mounts to surface using two #8 x 2"-long corrosion-resistant brass wood screws (included).  For 12-Volt fixtures only. TDM3:  Mount for directional fixtures with knuckle.  Use of SA accessory is recommended for directionals. TDM3-HANG:  Mount for hanging fixtures.  Includes bushing and locknut. Specifications
  • Tree / Beam Mount For Monopoint Directional Fixtures Using SA Accessory Two notches for surface-mounted wire Made from .063" thick spun yellow brass.  Mounts to surface using two #8 x 2"-long corrosion-resistant brass wood screws (included).  For 12-Volt fixtures only. TDM4:  Mount for directional fixtures with knuckle.  Use of SA accessory is recommended for directionals. TDM4-HANG:  Mount for hanging fixtures.  Includes bushing and locknut. Specifications

Title

Go to Top